ホーム > ブログ> Which factors will directly affect the effect of bag filter?

Which factors will directly affect the effect of bag filter?

October 13, 2021
1. Bag-type pulse dust collector vibration (can be checked from the following aspects);

Air Filter Baghouse 2

A. Impingement occurs when the impeller rotates. Abnormal sounds and intense vibrations may occur at this time. The reason is storage and transportation, installation, and deformation of the fan casing or impeller components during use.
b, storage and transportation, installation, use of the transmission or casing deformation impeller balance damage. The reasons are as follows: the impeller is deformed by pressure; the connection parts of the impeller and the sleeve are loose; the lifting of the shaft causes the main shaft to deform; the fixed screw of the motor loosens;
c Fan foot bolts are not tightened.

2. Heating: After operating for one hour at room temperature, if the temperature rise of the motor is found to be too high, it may be caused by one of the following reasons:

a The system's resistance is too large or the fan's matching is unreasonable, causing the motor to run overloaded. The reason is that the valve's resistance coefficient is too large or the valve's coefficient valve is not open.
b The motor bearing is damaged, the clearance is small and does not meet the requirements;
c The motor is in phase-failure operation or wiring error; d The power supply voltage is too low.

Bag type pulse dust collector has the following characteristics:

1 high dust removal efficiency, dust removal efficiency up to 99%;
2 adaptable, can handle different types of particles, processing capacity can vary;
(3) When the operation is flexible, and the concentration of dust in the inlet gas changes greatly, the dust removal efficiency is not greatly affected; (4) The structure is simple, and the utility model has the advantages of flexible use, easy recovery of dry materials, and no sludge treatment.

Factors affecting the dust removal effect of bag filter

(1) Selection of filter bags: The filter bags should be made of materials that are resistant to high temperatures, glass fiber/felt, NOMEX, needle felt, P84 needle felt, etc., taking into account the abrasion resistance, high temperature and durability of the filter bags. Costs and other factors, the general selection of copper industry NOMEX needle felt.
(2) Temperature control: Generally, the temperature of the NOMEX filter bag is 200 °C, so the inlet temperature of the processing facility should be controlled below 200 °C. When the flue gas passing through the long smoke pipe reaches the dust collector box, the temperature can be reduced to Below 200 °C, under special conditions, it can be water-cooled and coolers installed at the total smoke pipe.
(3) Fan selection: The induced draft fan is better than the blower.
(4) Mechanical dust removal is more convenient and clean than artificial dust removal, but the cost of mechanical dust removal is high, and pulse dust removal methods are mostly adopted.
(5) Leakage and resistance: theoretically, the dust collection efficiency of the bag-type pulse dust collector is 99%, but it cannot be achieved in the actual measurement, mainly due to the effects of air leakage and resistance. The lower the air leakage rate is, the better the dust removal effect is; Have a certain influence, often empty filter bag, reduce resistance, can improve the dust removal effect.
(6) The dust cover should be as close as possible to the burner, so that the dust can be more easily entered into the cover, increase the amount of dust collected, and reduce unorganized emission pollution.
(7) Equipment maintenance: equipment and cloth bags are easy to be damaged. Bags should be repaired and replaced in time.
(8) Airflow speed: At a flow rate of 1 to 3 m/s, the dust removal effect is best, and the general wind speed is controlled at 2 to 4 m/s.
(9) Filter area: The larger the filter area, the higher the dust removal efficiency, but the cost will increase accordingly. Therefore, the air volume should be calculated in advance, and then select the corresponding dust collector model.
(10) Secondary dust removal: The sedimentation chamber is installed in front of the dust collector box to form secondary dust removal. The settling chamber can remove a part of the large particle dust, lower the temperature, and reduce the dust collector pressure.
お問い合わせ

Author:

Mr. Jacky Guo

Phone/WhatsApp:

8613722852356

人気商品
You may also like
Related Categories

この仕入先にメール

タイトル:
イーメール:
メッセージ:

Your message must be betwwen 20-8000 characters

お問い合わせ

Author:

Mr. Jacky Guo

Phone/WhatsApp:

8613722852356

人気商品
We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

送信